DIY Stereo Yiroshi Power Amplifier 1400W

DIY Stereo Yiroshi Power Amplifier 1400W

This my second project for Yiroshi Power Amplifier Circuit, the power amplifier circuit is indeed very super quality, many have tested the strength of this Yiroshi power amplifier. Power amplifier yiroshi is suitable for outdoor or indoor. Previously I have made this yiroshi amp circuit in the mono version. I have also tested it in the unboxed state of the box, using only 2SC2922 and 2SA1943 final transistors, this amplifier is capable of high enough power until my speakers are damaged and also my smps is damaged This power amplifier is tough enough, none of my final transistors parallels broken.

here is the circuit scheme of the stereo power amplifier yiroshi, the scheme below is still the same with the yiroshi circuit that superpower driver before, only later will replace the transistor previously used TIP3055 and TIP2955 I replace it with transistor 2SC5200 and 2SA1943. Because the previous transistor has only a maximum voltage of 60Volt with a maximum current of 15Ampere, so it is advisable to use a larger transistor maximum voltage and current. If for 2SC5200 and 2SA1943 transistors this is enough for me, maximum CE CE voltage up to 230V and maximum current up to 15 Ampere.

In the above circuit scheme is a combined stereo of two series of yiroshi power amplifiers, so to list the components to make it easier for you to buy, please just look at the previous post here Yiroshi Power Amplifier Circuit.

To make it easier for this yiroshi amplifier circuit you can use this PCB Layout design:


PCB Final Transistor Parallel for stereo amplifier yiroshi driver.


DIY PCB AND ASSEMBLING COMPONENTS STEREO YIROSHI AMPLIFIER (VIDEO)

I have made this stereo yiroshi power amplifier circuit, but this is still in the test process stage. and it turns out for PCB Layout for the driver you have to reverse the position of all transistors, so the same face with the top component layout. Later you will be able to see the location and position of the transistor, after the power amplifier is finished and ready to be produced.

For the final transistor, on this yiroshi stereo amplifier project, I do not use transistor Toshiba 2sc5200 and 2sa1943 as well as sanken transistor 2sc2922 and 2sa1216.

I am using transistor NJW0302 and NJW0281, the transistor price of NJW0302 and NJW0281 is almost the same as Toshiba transistor 2sc5200 and 2sa1943.

Both transistors both have 150Watt power output, and IC 15Ampere but for VCEO and VCBO are different, a 20Volt difference is higher transistor NJW0302 and NJW0281, where the maximum voltage is 250Volt.

The following is a final transistor picture of NJW0302 which is embedded in the PCB:


And this is the final transistor image I've paralleled using the PCB Design layout above.I am using 14 pairs of NJW0302 and NJW0281 transistors and for per channel yiroshi driver I use 7 pairs of transistors.

Already tested power amplifier yiroshi I will supply with 20Ampere 60Volt Switching Mode Power Supply 


ASSEMBLING FINAL TRANSISTOR AND TEST POWER AMPLIFIER YIROSHI STEREO OUTPUT USING 14SET NJW0302 NJW2801.


Download File PCB Layout.PDF
PCB Stereo Yiroshi Amplifier
Transistor Final Top
Transistor Final Bottom

Komentar

Posting Komentar

Postingan populer dari blog ini

Problem RGB TV Cina Yang Sering Menjebak Teknisi

Gambar
Problem RGB TV Cina Yang Sering Menjebak Teknisi "> Diantara problem kerusakan TV Cina yang sering menjebak teknisi adalah bagian RGB. Ini dari hasil pengamatan Admin ketika membantu teman dalam menangani kerusakan seputar RGB TV Cina. Banyak sekali kesalahan prediksi yang berujung pada gagalnya menyelesaikan pekerjaan servis. Diantara problem RGB yang paling sering Admin temukan dan tidak semua teknisi paham dalam memperbaikinya adalah: Gambar buram kadang seperti pelangi berkabutGambar dominan di warna tertentuGambar muncul warna tertentu disertai dengan garis-garisGambar seperti kliseGambar blank putih bergarisWarna seleberanDan masih banyak lagi. Nah dari semua problem atau kerusakan seputar RGB TV cina diatas, akan saya bahas satu-persatu tentang penyebab pasti dan cara memperbaikinya. 1. Gambar buram kadang seperti pelangi berkabut Gambar buram dan terkadang seperti pelangi dipenuhi kabut sering dianggap teknisi adalah kerusakan tabung sudah lemah atau FBT rusak. T...
Baca selengkapnya

3000 Watts Power Amplifier Class D Mosfet IRFP260 / IRFP4227

Gambar
3000 Watts Power Amplifier Class D Mosfet IRFP260 / IRFP4227 3000W (3kW) Class D Power Amplifier Project using IC IR2110, CD4049 (HEF4049/HCF4049), NE555, LM311, and Op-Amp Comparator TL071 as the main stage amplifier, the driver stage using BD140/BD139 or you can use any driver stage power amplifier transistors. The Final Stage Amplifier using 4 x Mosfet Transistor IRFP260 or you can use IRFP250 / IRFP460 / IRFP4227. And do not forget to lose the importance of the LPF Filter. The advantages of this high power amplifier are: Strong Bass Boost, not SaggySecondary comfortable bias voltage (can be AC (transformer) / DC (adapter))Highly Efficient Rail - Stack LayoutOversized Heatsink & Output Coil (not easy saturation)Pulse Resolution Adjust Enable Below the Circuit Diagram of 3000W Class D Amplifier includes PCB Layout design: Component List Resistors 1/4W: 4R7 x 2, 10R x 5, 100R x1, 47R x 4, 1K x 8, 4K7 x 4, 100K x 3. Resistors 1W: 22R x 2 Resistors 2W:10R x 1 , 1K5 x 1...
Baca selengkapnya

High Power Class-D Amplifier D4K5

Gambar
High Power Class-D Amplifier D4K5 This High Power Amplifier circuit is a class D power amplifier, which has a high enough power to generate 1000W of power at 8 Ohm impedance - and also more power up to 2000W at 4 Ohm impedance. This Power Amplifier can generate great power if given enough power supply. For example, you can use 30A transformer with 100V symmetric voltage.  Here is the circuit scheme of High Power Class-D Amplifier D4K5: View larger schematic image here:  Power Amplifier Class-D D4K5 Component List Resistor R1, R3, R4, R9, R13, R18, R19, R20= 1K R2, R16, R39= 100K R5, R6= 10R R7, R8=6K8/2W R10, R21, R26, R27=4K7 R11, R17=6K8 R12=100R R14, R15=4R7 R22, R23, R24, R25, R31, R33=47R R28, R29, R30=0,1R/2W R36, R38=22R/2W R40=1K5/5W R41=10R/2W RV1=10K Trimpot Capacitor C1=10uF/16V C2=10N C3, C4=1N C5=470uF/16V C6=220uF/16V C7, C9, C11, C12, C13, C15, C16, C18, C19=100N MKP C8=470uF/16V C10, C14, C17=100uF/16V C20=10uF/50V C21, C22, ...
Baca selengkapnya